Photo etch parts

Scratchbuilding, kitbashing, reposing and other modifications.
User avatar
MEATLOAFr
Rampaging Rear Admiral (LH)
Rampaging Rear Admiral (LH)
Posts: 1902
Joined: Fri Sep 28, 2012 12:46 pm
Location: Lincoln, Nebraska

Photo etch parts

Postby MEATLOAFr » Thu Dec 19, 2013 2:48 am

I have a question about some photo-etched parts.

To anneal them, can I use a candle flame or does it have to be a butane torch?

I just don't want to go out and by one to find out it was overkill.

Also any tips/tricks to getting them to adhere to polystyrene and resin?

I'm doing the DLM phaser strips & other photo-etched accessories to a 1/1400 galaxy
If the world ends tomorrow, it's ALL YOUR FAULT!!!

Custom Decals, and Vinyl Cutting services available

User avatar
Tesral
Anything Goes Admiral
Anything Goes Admiral
Posts: 3006
Joined: Tue Dec 18, 2012 12:58 pm
Location: Dearborn, Mi -- at my desk.
Contact:

Re: Photo etch parts

Postby Tesral » Thu Dec 19, 2013 6:14 am

The latter answer is CA. The thin stuff. The former I don't know.
Garry AKA --Phoenix-- Rising above the Flames.
"I saw it done on Voyager" is no excuse for anything, even breathing.

User avatar
Moongrim
Fatidical Fleet Admiral (CW)
Fatidical Fleet Admiral (CW)
Posts: 4943
Joined: Tue Mar 12, 2013 9:36 pm
Location: West of Eugene Oregon.

Re: Photo etch parts

Postby Moongrim » Thu Dec 19, 2013 4:03 pm

From what I remember from the annealing I did with copper pipes back in tech school- is that you want the flame that will be annealing, hot enough to burn blue.

I'm afraid that a blue colored candle won't do.

However, if you do have spare/leftover/sprue etch kit parts, you could try such on a test piece of styrene.
There are Times, Sir, when men of good Conscience cannot blindly follow orders. You acknowledge their sentience, but ignore their personal liberties and freedoms. Order a man to hand over his child to the state? Not while I"m captain.
- J.L.Picard.

User avatar
MEATLOAFr
Rampaging Rear Admiral (LH)
Rampaging Rear Admiral (LH)
Posts: 1902
Joined: Fri Sep 28, 2012 12:46 pm
Location: Lincoln, Nebraska

Re: Photo etch parts

Postby MEATLOAFr » Fri Dec 20, 2013 2:49 am

well thanks, I'll cut a piece from the side and see what happens with the annealing and adhesion
If the world ends tomorrow, it's ALL YOUR FAULT!!!

Custom Decals, and Vinyl Cutting services available

User avatar
MEATLOAFr
Rampaging Rear Admiral (LH)
Rampaging Rear Admiral (LH)
Posts: 1902
Joined: Fri Sep 28, 2012 12:46 pm
Location: Lincoln, Nebraska

Re: Photo etch parts

Postby MEATLOAFr » Sat Jan 18, 2014 9:54 pm

Have a small butane torch comming that I bought off evilBay, hopefully it will work

then I will pick up some CA and test out on some scraps

Have a AGT Galaxy to build and have to modify some extra Photo-etch to the extra phaser strips on the Starcrafts add-on

I do wish the parts were in clear though, and the middle pylon was hollow, would make what I want to do to it so much easier
If the world ends tomorrow, it's ALL YOUR FAULT!!!

Custom Decals, and Vinyl Cutting services available

User avatar
Moongrim
Fatidical Fleet Admiral (CW)
Fatidical Fleet Admiral (CW)
Posts: 4943
Joined: Tue Mar 12, 2013 9:36 pm
Location: West of Eugene Oregon.

Re: Photo etch parts

Postby Moongrim » Sun Jan 19, 2014 1:18 am

But if it was easier....it'd be....well....I guess....my train of thought got derailed... :imsorry:
There are Times, Sir, when men of good Conscience cannot blindly follow orders. You acknowledge their sentience, but ignore their personal liberties and freedoms. Order a man to hand over his child to the state? Not while I"m captain.
- J.L.Picard.

User avatar
Greyryder
Can-Do Captain
Can-Do Captain
Posts: 545
Joined: Sat Aug 03, 2013 4:06 am
Contact:

Re: Photo etch parts

Postby Greyryder » Sun Jan 19, 2014 1:21 am

Moongrim wrote:But if it was easier....it'd be....well....I guess....my train of thought got derailed... :imsorry:


Probably shouldn't have used Penn Central. :P

jjsmn
Erratic Ensign
Erratic Ensign
Posts: 8
Joined: Wed Feb 24, 2016 10:58 pm

Re: Photo etch parts

Postby jjsmn » Sun Feb 28, 2016 1:24 am

With regard to annealing in brass, when I was heavily into wooden ship modeling, the recommendation was always to quench the brass in water when red hot to anneal. That's the way I did it, and the brass did turn out soft. This is totally different than what is done with steels and other hard metals. I think it may have to do with brass being copper based.

I am not sure what the current brass annealing wisdom is?? :shock: Looking at the internet, I get the feeling that it may not hurt to quench, but am not sure whether it is necessary to quench.

Any thoughts???

Not trying to hijack thread! :mrgreen:

JJS

User avatar
Kremin
Charismatic Commander
Charismatic Commander
Posts: 402
Joined: Mon Jul 14, 2014 12:26 am
Location: North East England

Re: Photo etch parts

Postby Kremin » Mon Feb 29, 2016 10:46 am


User avatar
MEATLOAFr
Rampaging Rear Admiral (LH)
Rampaging Rear Admiral (LH)
Posts: 1902
Joined: Fri Sep 28, 2012 12:46 pm
Location: Lincoln, Nebraska

Re: Photo etch parts

Postby MEATLOAFr » Tue Mar 01, 2016 3:19 am

Image

whoa, forgot about this - and here I was actually looking at the parts yesterday and daydreaming about working on it today
If the world ends tomorrow, it's ALL YOUR FAULT!!!

Custom Decals, and Vinyl Cutting services available


Return to “Customizing”

Who is online

Users browsing this forum: No registered users and 18 guests